93.1. ISDN disconnection codes

93.1.1. ISDN disconnection codes recommended by ITU (formerly CCITT)

The parameter CAUSE in the debug log shows a “cause” field which corresponds to what has been specified by the ITU in Recommendations Q.931 e Q.850.

Example: CAUSE: 82 90

Table 93.1. Disconnection code's format

 First field: LocationSecond field: ISDN disconnection cause
CAUSE8290
DescriptionPublic network serving the local user (LN)Normal call clearing

Table 93.2. First Field: Location

Code value (hex)LocationBrief Description
80User (U)Originated by user equipment, i.e phone.
81Private network serving the local user (LPN)Generated by a private networking device, e.g. a PABX, on the side which is directly connected to the receiving device.
82Public network serving the local user (LN)Generated by the public network, e.g. a Telco, on the side which is directly connected to the receiving device.
83Transit network (TN)Generated somewhere in an intermediate network on which the call is transiting.
84Public network serving the remote user (RN)Generated by the public network, e.g. a Telco, on the remote side respect to the receiving device.
85Private network serving the remote user (RPN)Generated by a private networking device, e.g. a PABX, on the remote side respect to the receiving device.
87International network (INTL)Generated somewhere in the international network.
8ANetwork beyond interworking point (BI)Generated by a non-ISDN network interconnected to the ISDN network.
F0CPX internal codeGenerated by Abilis.
FFCPX internal codeGenerated by Abilis.
XXAll other values are reserved. 

Table 93.3. Second field: ISDN disconnection cause

Code value (hex)ISDN disconnection cause
81Unallocated (unassigned) number. This cause indicates that the called party cannot be reached because, although the called party number is in a valid format, it isn't currently allocated (assigned).
82No route to specified transit network (national use). This cause indicates that the equipment sending this cause has received a request to route the call through a particular transit network which it does not recognize. The equipment sending this cause does not recognize the transit network either because the transit network does not exist or because that particular transit network, while it does exist, does not serve the equipment which is sending this cause. This cause is supported on a network-dependent basis.
83No route to destination. This cause indicates that the called party cannot be reached because the network through which the call has been routed does not serve the destination desired. This cause is supported on a network-dependent basis.
84Send special information tone. This cause indicates that the called party cannot be reached for reasons that are of a long term nature and that the special information tone should be returned to the calling party.
85Misdialled trunk prefix (national use). This cause indicates the erroneous inclusion of a trunk prefix in the number of the called party.
86Channel unacceptable. This cause indicates that the channel most recently identified isn't acceptable to the sending entity for use in this call.
87Call awarded and being delivered in an established channel. This cause indicates that the user has been awarded the incoming call, and that the incoming call is being connected to a channel already established to that user for similar calls (e.g. packet-mode X.25 virtual calls).
88Preemption. This cause indicates that the call is being preempted.
89Preemption - circuit reserved for reuse. This cause indicates that the call is being preempted and the circuit is reserved for reuse by the preempting exchange.
90Normal call clearing. This cause indicates that the call is being cleared because one of the users involved in the call has requested that the call be cleared. Under normal situations, the source of this cause isn't the network.
91User busy. This cause is used to indicate that the called party is unable to accept another call because the user busy condition has been encountered. This cause value may be generated by the called user or by the network. In the case of user determine user busy, it's noted that the user equipment is compatible with the call.
92No user responding. This cause is used when a called party does not respond to a call establishment message with either an alerting or connect indication within the prescribed period of time allocated.
93No answer from user (user alerted). This cause is used when the called party has been alerted but does not respond with a connect indication within a prescribed period of time. NOTE - This cause isn't necessarily generated by Q.931 procedures but may be generated by internal network timers.
94Subscriber absent. This cause value is used when a mobile station has logged off, radio contact isn't obtained with a mobile station or if a personal telecommunication user is temporarily not addressable at any user-network interface.
95Call rejected. This cause indicates that the equipment sending this cause does not wish to accept this call, although it could have accepted the call because the equipment sending this cause is neither busy nor incompatible. This cause may also be generated by the network, indicating that the call was cleared due to a supplementary service constraint. The diagnostic field may contain additional information about the supplementary service and the reason for rejection.
96Number changed. This cause is returned to a calling party when the called party number indicated by the calling party is no longer assigned. The new called party number may optionally be included in the diagnostic field. If a network does not support this cause value, cause No. 1, unallocated (unassigned) number shall be used.
9ANon-selected user clearing. This cause indicates that the user has not been awarded the incoming call.
9BDestination out of order. This cause indicates that the destination indicated by the user cannot be reached because the interface to the destination isn't functioning correctly. The term “not functioning correctly” indicates that a signalling message was unable to be delivered to the remote party; e.g. a physical layer or data link layer failure at the remote party, or user equipment off-line.
9CInvalid number format (address incomplete). This cause indicates that the called party cannot be reached because the called party number isn't in a valid format or isn't complete. NOTE - This condition may be determined immediately after reception of an ST signal or on time-out after the last received digit.
9DFacility rejected. This cause is returned when a supplementary service requested by the user cannot be provided by the network.
9EResponse to STATUS ENQUIRY. This cause is included in the STATUS message when the reason for generating the STATUS message was the prior receipt of a STATUS ENQUIRY message.
9FNormal, unspecified. This cause is used to report a normal event only when no other cause in the normal class applies.
A2No circuit/channel available. This cause indicates that there is no appropriate circuit/channel presently available to handle the call.
A6Network out of order. This cause indicates that the network isn't functioning correctly and that the condition is likely to last a relatively long period of time; i.e. immediately re-attempting the call isn't likely to be successful.
A7Permanent frame mode connection out-of-service. This cause is included in a STATUS message to indicate that a permanently established frame mode connection is out-of-service (e.g. Due to equipment or section failure) (see Annex A/Q.933).
A8Permanent frame mode connection operational. This cause is included in a STATUS message to indicate that a permanently established frame mode connection is operational and capable of carrying user information (see Annex A/Q.933).
A9Temporary failure. This cause indicates that the network isn't functioning correctly and that the condition isn't likely to last a long period of time; i.e. the user may wish to try another call attempt almost immediately.
AASwitching equipment congestion. This cause indicates that the switching equipment generating this cause is experiencing a period of high traffic.
ABAccess information discarded. This cause indicates that the network could not deliver access information to the remote user as requested, i.e. user-to-user information, low layer compatibility, high layer compatibility, or sub-address, as indicated in the diagnostic. It's noted that the particular type of the access information discarded is optionally included in the diagnostic.
ACRequested circuit/channel not available. This cause is returned when the circuit or channel indicated by the requesting entity cannot be provided by the other side of the interface.
AEPrecedence call blocked. This cause indicates that there are no preemptable circuits or that the called user is busy with a call of equal or higher preemptable level.
AFResource unavailable, unspecified. This cause is used to report a resource unavailable event only when no other cause in the resource unavailable class applies.
B1Quality of Service not available. This cause is used to report that the requested Quality of Service, as defined in Recommendation X.213, cannot be provided (e.g. Throughput or transit delay cannot be supported).
B2Requested facility not subscribed. This cause indicates that the user has requested a supplementary service which is implemented by the equipment which generated this cause, but which the user isn't authorized to use.
B5Outgoing calls barred within CUG. This cause indicates that although the calling party is a member of the CUG for the outgoing CUG call, outgoing calls aren't allowed for this member of the CUG.
B7Incoming calls barred within CUG. This cause indicates that although the called party is a member of the CUG for the incoming CUG call, incoming calls aren't allowed to this member of the CUG.
B9Bearer capability not authorized. This cause indicates that the user has requested a bearer capability which is implemented by the equipment which generated this cause but which the user isn't authorized to use.
BABearer capability not presently available. This cause indicates that the user has requested a bearer capability which is implemented by the equipment which generated this cause but which isn't available at this time.
BEInconsistency in designated outgoing access information and subscriber class. This cause indicates that there is an inconsistency in the designated outgoing access information and subscriber class.
BFService or option not available, unspecified. This cause is used to report a service or option not available event only when no other cause in the service or option not available class applies.
C1Bearer capability not implemented. This cause indicates that the equipment sending this cause does not support the bearer capability requested.
C2Channel type not implemented. This cause indicates that the equipment sending this cause does not support the channel type requested.
C5Requested facility not implemented. This cause indicates that the equipment sending this cause does not support the requested supplementary service.
C6Only restricted digital information bearer capability is available (national use). This cause indicates that the calling party has requested an unrestricted bearer service, but that the equipment sending this cause only supports the restricted version of the requested bearer capability.
CFService or option not implemented, unspecified. This cause is used to report a service or option not implemented event only when no other cause in the service or option not implemented class applies.
D1Invalid call reference value. This cause indicates that the equipment sending this cause has received a message with a call reference which isn't currently in use on the user-network interface.
D2Identified channel does not exist. This cause indicates that the equipment sending this cause has received a request to use a channel not activated on the interface for a call. For example, if a user has subscribed to those channels on a primary rate interface numbered from 1 to 12 and the user equipment or the network attempts to use channels 13 through 23, this cause is generated.
D3A suspended call exists, but this call identity does not. This cause indicates that a call resume has been attempted with a call identity which differs from that in use for any presently suspended call(s).
D4Call identity in use. This cause indicates that the network has received a call suspended request containing a call identity (including the null call identity) which is already in use for a suspended call within the domain of interfaces over which the call might be resumed.
D5No call suspended. This cause indicates that the network has received a call resume request containing a call identity information element which presently does not indicate any suspended call within the domain of interfaces over which calls may be resumed.
D6Call having the requested call identity has been cleared. This cause indicates that the network has received a call resume request containing a call identity information element indicating a suspended call that has in the meantime been cleared while suspended (either by network timeout or by the remote user).
D7User not member of CUG. This cause indicates that the called user for the incoming CUG call isn't a member of the specified CUG or that the calling user is an ordinary subscriber calling a CUG subscriber.
D8Incompatible destination. This cause indicates that the equipment sending this cause has received a request to establish a call which has low layer compatibility, high layer compatibility, or other compatibility attributes (e.g. data rate) which cannot be accommodated.
DANon-existent CUG. This cause indicates that the specified CUG does not exist.
DBInvalid transit network selection (national use). This cause indicates that a transit network identification was received which is of an incorrect format as defined in Annex C/Q.931.
DFInvalid message, unspecified. This cause is used to report an invalid message event only when no other cause in the invalid message class applies.
E0Mandatory information element is missing. This cause indicates that the equipment sending this cause has received a message which is missing an information element which must be present in the message before that message can be processed.
E1Message type non-existent or not implemented. This cause indicates that the equipment sending this cause has received a message with a message type which it does not recognize either because this is a message not defined or is defined but not implemented by the equipment sending this cause.
E2Message not compatible with call state or message type non-existent or not implemented. This cause indicates that the equipment sending this cause has received a message such that the procedures do not indicate that this is a permissible message to receive while in the call state, or a STATUS message was received indicating an incompatible call state.
E3Information element/parameter non-existent or not implemented. This cause indicates that the equipment sending this cause has received a message which includes information element(s)/parameter(s) not recognized because the information element identifier(s)/parameter name(s) aren't defined or are defined but not implemented by the equipment sending the cause. This cause indicates that the information element(s)/parameter(s) were discarded. However, the information element isn't required to be present in the message in order for the equipment sending the cause to process the message.
E4Invalid information element contents. This cause indicates that the equipment sending this cause has received an information element which it has implemented; however, one or more fields in the information element are coded in such a way which has not been implemented by the equipment sending this cause.
E5Message not compatible with call state. This cause indicates that a message has been received which is incompatible with the call state.
E6Recovery on timer expiry. This cause indicates that a procedure has been initiated by the expiry of a timer in association with error-handling procedures.
E7Parameter non-existent or not implemented - passed on (national use). This cause indicates that the equipment sending this cause has received a message which includes parameters not recognized because the parameters aren't defined or are defined but not implemented by the equipment sending the cause. The cause indicates that the parameter(s) were ignored. In addition, if the equipment sending this cause is an intermediate point, then this cause indicates that the parameter(s) were passed on unchanged.
EEMessage with unrecognized parameter discarded. This cause indicates that the equipment sending this cause has discarded a received message which includes a parameter that isn't recognized.
EFProtocol error, unspecified. This cause is used to report a protocol error event only when no other cause in the protocol error class applies.
FFInterworking, unspecified. This cause indicates that there has been interworking with a network which does not provide causes for actions it takes. Thus, the precise cause for a message which is being sent cannot be ascertained.

93.1.2. Abilis CPX private ISDN disconnection codes

In Events Log messages it's sometimes possible to find codes which aren't codified by ITU, or are codified as “specific for the specified location: user”. These are specific codes used by CPX to indicate particular events.

Codes starting with F0 as the first byte, report local problems, i.e. they aren't messages sent or received by the network. Codes starting with FF as the first byte, are codes specific to CPX, sent or received by the network.

It should be noted that these “private” codes might not be transported to their destination by ISDN, exactly as happens with the Italian Telecom network.

Table 93.4. Abilis CPX private ISDN disconnection codes

Cause codes (hex)Meaning
00No problem detected.
91User busy.
93No answer from user (user alerted).
95Call rejected.
97Unconditional disconnect timer expiry.
A0Invalid number format (NRC_BADNUM).
A1No path between 2 B channels.
A2No codec available.
A3Cause code unavailable.
A4No AC available.
A5Destination out of order (NRC_L1DOWN). Level 1 of the ISDN is inactive.
A6Destination out of order (NRC_L2DOWN). Level 2 of the ISDN is inactive, or failed to activate.
A7No HDLC available.
A8No port available (NO_PORT).
A9Temporary failure.
AANo EEC available.
ABNo AC with fax relay available.
ACNo MCD available.
ADNo outgoing connection side detected.
AENo appropriate connection for Call Pickup.
B3No circuit or channel available (NRC_NOCHAN).
B4Loop connection detected.
B5Not enough bandwidth.
B6CTI service denied.
B7CTI service error.
BECTIR administratively disabled.
BFCTI service not available.
D8Incompatible destination.
DFInvalid message, unspecified.
FFNormal call clearing, unspecified.